GE IS200ADIIH: IS200 ADII Auxiliary ISBus Interface Board
Overview
The IS200ADIIH is an Auxiliary ISBus (Innovation Series™ Bus) Interface Board (ADII) designed to interface an AcDc2000 drive to an ISBus Local Area Network (LAN). The board resides on the backside of the first board carrier of the AcDc2000 drive, providing a critical communication link between the drive and its control system.
This interface board is an essential component for integrating AcDc2000 drives into Innovation Series drive systems, enabling seamless data exchange and control functionality.
Functional Description
Communication Architecture
The ADII board connects to the DS200LDCC Drive Control/LAN Communications board (LDCC) through:
LNPL ribbon cable
COM1 wire
Power is supplied to the ADII board through the 2PL power cable from the AcDc2000 drive's power supply board.
Key Functional Features
Bypass Relay: The ADII board includes a bypass relay to maintain ISBus electrical continuity if the drive is powered down — no external bypass module is required.
Signal Mapping: The interface signal map is derived from the Innovation Series drive system applications signal map. Many references and feedbacks are generic, and AcDc2000 drive blockware must be created to imitate the Innovation Series drive functionality.
Integer Variable Mapping: The ADII board provides an integer variable map between the drive and controller. The integers must be scaled to the AcDc2000 units (given in the signal map definition).
Configuration
Configuration of the interface is done with either:
Refer to the Data Mapping section for detailed configuration information.
Hardware Design
The ADII board has no fuses or hardware jumpers. For information on LED indicators, test points, and connectors, refer to the Application Data section.
Note: The ADII board can only be used in AcDc2000 drives that have the LDCC board. It cannot be used with previous design drive control and LAN communication boards.
Installation Procedures
⚠️ Safety Warnings
Warning: To prevent electric shock, turn off power to the drive, then test to verify that no power exists in the drive before touching it or any connected circuits.
Caution: To prevent equipment damage, do not remove, insert, or adjust board connections while power is applied to the equipment.
Step-by-Step Installation
De-energize the drive: Make sure that the drive in which the board is to be installed has been de-energized. (Refer to the appropriate User's Guide for complete de-energizing procedures and follow all local practices of lock-out/tag-out.)
Open the drive's cabinet door. Using equipment designed for high voltages, test any electrical circuits before touching them to ensure that power is off.
Install the ADII board in the drive as follows:
a. Release the two board carrier retainers by pulling them forward.
b. Lift up and rotate the front board carrier out and down until it is resting on its stops.
c. Place the board in position on the four tabs (on the left side) of the back of this board carrier and press it firmly into position on these tabs.
Connect the LNPL ribbon cable into the LNPL connector on the ADII board and the LNPL connector on the LDCC board.
Connect the COM1 wire onto the E1 (COM1) stab-on terminal on the ADII board and the E1 (COM1) terminal on the LDCC board.
Install the CHASSIS wire onto the E2 stab-on terminal on the ADII board and secure the other end to an accessible screw on the drive chassis.
Caution: The chassis wire must be securely mounted to the drive's chassis to shunt the ISBus shield to ground. Care must be taken to keep the chassis wire tight to the ADII board and away from the power supply board at all times. Use a wire tie-down strap connected to the bottom of the board carrier to keep it away from the power supply board.
Plug the 2PL cable connector into the 2PL receptacle on the ADII board.
Install an ISBus cable into the RXIN RJ45 jack (P3) on the ADII board and the TXOUT jack (P2) of the previous device on the ISBus.
Install an ISBus cable into the TXOUT RJ45 jack (P2) on the ADII board and the RXIN jack (P3) of the next device on the ISBus.
Compatibility & Requirements
Compatible Drive | AcDc2000 drive with LDCC board |
Incompatible With | Previous design drive control and LAN communication boards |
Configuration Tools | Local keypad on LDCC board or GE Control System Toolbox |
Power Source | 2PL power cable from AcDc2000 power supply board |
Communication Interface | LNPL ribbon cable and COM1 wire to LDCC board |
Why Choose the IS200ADIIH?
Seamless Integration | Directly interfaces AcDc2000 drives to ISBus LAN |
No External Bypass Needed | Built-in bypass relay maintains ISBus continuity |
Flexible Configuration | Configure via local keypad or GE Control System Toolbox |
Robust Design | No fuses or hardware jumpers to fail |
Clear Diagnostics | LED indicators, testpoints, and connectors for easy troubleshooting |
IS200TSVCH1A
IS200TTURH1CFD
IS200TVBAH2ACC
IS200VCRCH1B
IS200VSVOH1B
IS200VSVOH1BDC
IS200VTURH2BAC
IS200VVIBH1CAC
IS200WNPSH1ABA
IS210AEBIH1BED
IS210AEDBH4AGD
IS210SAMBH2AA
IS210WSVOH1AE
IS215UCVEH2A
IS215UCVEM06A
IS215UCVEM09B
IS215VCMIH2C
IS215VPROH1BD
IS220PAICH2A
IS220PDIAH1B
IS220PDIOH1B
IS220PRTDH1A
IS220PRTDH1B
IS220PSVOH1A
IS220PSVOH1B
IS220PTURH1B
IS220UCSAH1A
IS220YDIAS1A
IS230SNCIH6A
IS230TCISH6C
IS230TNCIH4C
IS230TVBAH2A
IS420UCSBH1A
