Introduction
This document serves as a reference for the connection, commissioning and operation of the   MPB1-TP and MPB2-TP communication cards. These cards must only be used in MICRO PANEL devices (XV400) which provide the appropriate slot (destination hardware).

It must be ensured that the cards are only fitted or removed from the device when the power supply is switched off.

The MPB1-TP supports all drivers and physical interfaces for a wide range of PLC types which are described later in this documentation. In addition to the MPB1-TP drivers, the MPB2-TP also supports the MPI interface for the SIMATIC S7. Apart from this, both cards are completely identical.

The term MPBx-TP will be used in this documentation unless the functions of all cards are different. MPBx-TP means MPB1-TP and MPB2-TP.

Remember that the MPB1-TP and the MPB2-TP card are factory set with   RS485 default configuration.
INTERFACE CONNECTION MPB2-TP

The MPB2-TP card is equipped with two interfaces. These interfaces cannot be linked (switched) at the same time. It would cause incalculable communication conflicts.

Remark : Only one interface can be linked.

CONFIGURATION
MPB1-TP

COM PORT 
The COM PORT interface can be configured via the jumpers for RS232, TTY RS422 and RS485 protocols. See also Interface configuration for information how to configure the interfaces.
ERROR
When lit, the ERROR LED (red) indicates that the last data transfer to the PLC was not executed correctly. The LED will not go out until the next data transmission to the PLC is executed correctly. This LED should never be lit in normal operation.
ACTIV
The green LED should be lit during an active data transfer between the MPB1-TP and the PLC. In normal operation this LED should flash briefly (approx. 50 ms) with every data transmission.
MPB2-TP
COM PORT
The COM PORT interface can be configured via the jumpers for RS232, TTY RS422 and RS485 protocols. See also Interface configuration for information how to configure the interfaces.
MPI
The MPI interface must only be used for the SIMATIC S7 and must be configured for RS485. See also Interface configuration for information how to configure the interfaces.
ERROR
When lit, the ERROR LED (red) indicates that the last data transfer to the PLC was not executed correctly. The LED will not go out until the next data transmission to the PLC is executed correctly. This LED should never be lit in normal operation.
ACTIV
The green LED should be lit during an active data transfer between the MPB2-TP and the PLC. In normal operation this LED should flash briefly (approx. 50 ms) with every data transmission.
MPBX-TP
The MPBx-TP firmware is stored on a retentive flash memory for standard and alternative drivers.

The following drivers are factory set: 

 • the latest MPBx-TP compatible standard drivers (MPB.BIN) - 

 • and as alternative drivers: on MPB1-TP the latest Moeller PS40 PLC driver (PS40.BIN) - on MPB2-TP the latest SIMATIC S7 driver (MPI.BIN).   The drivers can be updated at any time via the serial interface (see section 3.3) or in a MICRO PANEL (see appropriate documentation for MICRO PANEL).

MPBX-TP LOADING PROGRAM
This document describes how to load the firmware for the MPBx-TP using the COM PORT provided on the card. Simple load features are also provided on the MICRO PANEL. These are described in the relevant device descriptions. 

ACCESSORIES

- Load cable (see section 3.4) - Load program (COMLOAD.EXE) at least version 2.00 

- PC with serial interface (COM1 or COM2) 

- Firmware files (MPB.BIN,MPI.BIN, PS40.BIN.
PROCEDURE
1. Remove the card from the MICRO PANEL (with the power supply switched off, i.e. de energized).
2.Configure the COM PORT of the MPBx-TP for RS232 (section 2.2)
3.Set jumper J6 on the MPBx-TP to PRG.

4.Fit the card back into the slot of the MICRO PANEL.

5.Connect the load cable to the serial interface of the PC (COM1 or COM2) and the COM PORT of the MPBx-TP.

Eaton S811+N66N3S Softstart(Cont act us to confirm current prices)

EATON CORPORATION XP48D34B75CUS6 / XP48D34B75CUS6 (BRAND NEW)

EATON CORPORATION XDT3C75X / XDT3C75X (BRAND NEW)

EATON CORPORATION XDT3E75X / XDT3E75X (BRAND NEW)

Eaton Leonard VB42 tube bender with bed extension  dies  mandrel lube

Eaton Leonard VB42 tube bender with bed extension  dies  mandrel lube

EATON CORPORATION CUTLER HAMMER RD316T36WP01Z0 2 BREAKER 3 POLE  1600 AMP FRAME

EATON CORPORATION CHES-606020-4X SS6 / CHES6060204XSS 6 (BRAND NEW)

EATON CORPORATION XDT3F75X / XDT3F75X (BRAND NEW)

EATON CORPORATION CH747224-4XSS6 FD / CH7472244XSS6F D (BRAND NEW)

EATON CORPORATION CHES-606016-4X SS6 / CHES6060164XSS 6 (BRAND NEW)

EATON CORPORATION CHES-727224-4X S / CHES7272244XS (BRAND NEW)

EATON VCOM-250 EATON VCOM LICENSING - 250 NODES

EATON CORPORATION CHES-604820-4X SS6 / CHES6048204XSS 6 (BRAND NEW)